Page 73 - ZF-Catalog-ZSi-Foster-08-19-R3

W601 Channel Loads 19 Gauge - 13⁄16" x 15⁄8" (21mm x 41mm)
Channel Part No.
Wt./Ft. Lbs. (Kg/M)
Area of Section Sq. in. (Sq. cm)
X-X Axis
Y-Y Axis
4 (lx cm4)
lx in.
3 (Sx cm3)
Sx in.
rx. in. (rx. cm)
4 (ly cm4)
ly in.
3 (Sy cm3)
Sy in.
ry in. (ry cm)
W600
0.36
(0.54)
0.107
(0.69)
280
280
280
280
280
270
230
160
110
Section Properties
0.009 0.020 0.295 0.012
(0.37) (0.33) (0.75) (0.50)
0.029
(0.48)
* 1.2 * 1.2 * 1.2 * 1.2 * 1.2
1.1 0.8 0.5 0.4 0.3
0.333
(0.85)
1.2 * 1.2 * 1.2 * 1.2 * 1.0
0.8 0.6 0.4 0.3 0.2
18.3
15.7
13.7
11.2
8.3
6.0
4.6
**
**
**
W601 - Allowable Beam Loads
Span
Max. Uniform Load (W)
Deflection at Load (W)
Uniform Load at Deflection
Span /180
Span /240
Span /360
In
Lbs
In
Lbs
Lbs
Lbs
Span
Max. Uniform Load (W)
Deflection at Load (W)
Uniform Load at Deflection
Span /180
Span /240
Span /360
mm
kN
mm
kN
kN
kN
12
18
24
30
36
42
48
60
72
84
280
280
280
280
280
270
230
190
160
130
* * * * *
0.00
0.02
0.04
0.07
0.13
0.20
0.25
0.40
0.58
0.75
* * * * *
280 * 280 * 280 * 280 * 280 * 240
180 120 80
280 * 300 1.2 280 * 450 1.2 280 * 600 1.2 280 * 750 1.2 220 900 1.2
* 0.11
* 0.39
* 0.92
* 1.79
* 3.10
4.74
6.29
9.73
14.16
19.67
1.2
1.2
1.2
1.2
1.2
1.2
1.1
0.7
0.5
0.4
* * * * *
160 120 80 50
1,050 1.2 1,200 1.1 1,500 0.8 1,800 0.7 2,100 0.6
80 60 40
W601 - Allowable Column Loads
Unbraced Height
Max. Slot Face Load
Max. Column Load Applied at C.G.
K = 0.65
K = 0.80
K = 1.0
K = 1.2
In
Lbs
Lbs
Lbs
Lbs
Lbs
Unbraced Height
Max. Slot Face Load
Max. Column Load Applied at C.G.
K = 0.65
K = 0.80
K = 1.0
K = 1.2
mm
kN
kN
kN
kN
kN
12
18
24
30
36
42
48
60
72
84
1,240
1,210
1,170
1,130
1,070
990
900
710
550
**
4,650
4,330
3,980
3,660
3,380
3,140
2,930
2,180
1,530
4,510 4,300
4,090 3,780
3,680 3,340
3,340 3,010
3,060 2,460
2,690 1,900
2,230 1,460
1,460 930
1,010 **
4,090
3,500
3,060
2,460
1,800
1,320
1,010
**
**
300 5.5
450 5.4
600 5.2
750 5.0
900 4.8
1,050 4.4
1,200 4.0
1,500 3.2
1,800 2.5
2,100 2.0
20.7
19.3
17.8
16.4
15.1
14.1
13.2
20.1
18.3
16.5
14.9
13.7
12.2
10.2
19.2
16.9
14.9
13.5
11.2
8.7
6.7
1,130 ** ** **
9.9 6.7 4.3
7.0 4.6 **
5.2 3.4 **
* Load limited by spot weld shear
** KL ⁄ r > 200
NR = Not Recommended
Beam loads shown are total uniform load, including the channel weight, for a simple span supported at each end that is adequately laterally braced. Refer to pages 20 -23 for other beam support conditions.
Refer to page 77 for load reduction factor for an unbraced beam length.
ZSi-Foster Engineering Catalog
– 73 –
WARNING: These products can expose you to chemicals including lead, which is known to the State of California to cause cancer, and which is known to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Technical Gamma Rooftop Concrete Beta Clamps Loop & Ring Spring Electrical Pipe & Conduit General Channel Nuts Channel Introduction Data Pads Supports Inserts & Z-Clamps Clamps Steel Fittings Supports Fittings & Hardware